Tap in our daily life is very frequent, it is not strange to us, but the regular use of the structure of the faucet and faucet working principle is the kind of it, may not be very clear. The following is to explain in detail the structure of the tap water and the principle, we have a comprehensive understanding of the water faucet.

        In accordance with the use of tap water classification, in our life, the common faucet with three kinds: the use of kitchen dishes to wash dishes, the use of the bathroom sink faucet, bathtub faucet. The following are based on their different types to explain the structure and principle of the faucet.

       Faucet structure diagram and principle. From the graph, we can see that is a simple basin faucet figure, it is single to ceramic core surface, is mainly composed of a handle, a valve core, a water inlet braided hose and installation of small parts. Ceramic valve working principle of: general ceramic valve core bottom is formed by three holes, which two holes a for import and cold water, another for import and hot water, and the remaining one for internal the valve outlet, the composition of the concrete structure can view renderings.

        Valve core faucet cold and hot two holes have sealing ring, guarantee and main ramp street in sealing state, cold and hot water brass body connected to ensure the pipeline and the valve core of two holes on a one-to-one basis corresponding heat pipe and a cold water pipe. The main control valve opening and closing state of the two hole, relying on two ceramic pieces shown below in the mobile map to work. Fig. two schematic diagram of the top and bottom of the diagram are respectively the valve core separation and combination chart.

          We take the most left hole for hot water out of the hole, the right side of the cold out of the hole, the handle switch to drive the valve stem to move, so that the green ceramic film in the figure moves, the left and right two holes are sealed. Valve spool to the point where the flow of water must be through the spool to enter the main water channel, so no water into the spool, then there is no water out of the pipe. This is the water pipe off condition, the structure and working principle of the tap.
         Next, the water tap is the structure and working principle. When we turn the tap to the water in the state, led the green ceramic pieces to move, so that the left side of the figure is fully opened, the right side of the hole completely closed. So that the water can not enter the spool, hot water into the spool, a small space inside the six spool, as shown in the image above the green ceramic pieces of irregular holes. After doing the hole flow into the main body, which is the hot water out of the working principle. Turn the handle to the right side is the cold water, the middle cold and hot water pipes at the same time open, the outflow is warm water.
       The structure and principle of the basin water tap is mainly composed of a spiral valve core, which mainly depends on the rotation of the valve stem, and shifts the thread through the screw thread to achieve the effect of the opening and closing of the water inlet hole. When we rotate the stem, the thread bite, so that the end of the spool seal forward, back, the specific structure of the effect can be fancy. When we put the spool twisted into, the water inlet is sealed, and sealing the outlet position, rely on the valve seal end to seal the water outlet to realize the cold water and hot water alternately.

         Working principle of screw tap spool is mainly through the rotation of the valve stem, the above t thread displacement, to realize the hole switch. When we rotate the stem, it's a thread. Valve core seal to go in, or back, into the role of closing down, the back is the role of water.

         Dish basin faucet internal structure: water into braided tube body separate channels to ensure the latest water flowing through the valve core, from figure in ceramic green sheet flows through, yellow ceramic perforation is flow into the subject. The water and the main contact is a small space for pipe connection.

         Bathtub faucet structure and working principle: the general bathtub faucet is through the S shift to the water into the main body, but the first to enter the spool, from the spool into the main body. As above faucet structure diagram shown in water into the holes in the main body of the commutator on the left, the commutator provided to realize water opening and closing. 

         Faucet inside the working principle of commutator commutator through the sealing ring and the main body with the realization of the inner body foaming device and shower channel switching function. Note that the commutator we see in the example above, the center line should be symmetrical, asymmetrical words appear Water Leakage.
         Water pressure environment of water tap
         Daily use, the water pressure from the tap water is generally 3-5 kg, equivalent to 0.3-0.5Mpa. If the pressure is more than 6 kg, is a high water pressure, flush when the human body feel unwell. If the pressure is less than 3 kg, you can think the water pressure is low.
Scope of application
         Suitable for the use of Stars Hotel, hotels, public places, hospitals, home and so on, is the ideal choice for your pursuit of noble, elegant life!